Tools and Materials
Parts Enclosed with the Serenity Light and Music System:
- Light and Sound fixture
- Transformer: 120V input, 12V output
- Hardware
- 20 foot data cable
- Installation instructions & warranty info
- Clear Silicone
- Bluetooth Adapter Kit
Materials Needed:
- Drill
- 7/16" drill bit
- Tile cutter or grinder
- Other materials as required
- Ply Wood Backing Board
- Material/Hardware as required
- Amplified FM antenna with coax cable (for best results contact antenna supplier for best antenna location)
- Set of RCA audio cables (if you are planing on connection audio source)
- Installed 120v outlet near the Serenity Light and Music System
YOU WILL NEED ACCESS FROM THE ABOVE IN ORDER TO INSTALL THE SERENITY LIGHT AND MUSIC SYSTEM
Installing connections and placing the Serenity Light and Music System
Install the Serenity Light and Music System according to the installation and operation instructions. Failure to do so may result in an inoperative product and a hazardous condition.
Do not pinch, nail, staple wedge etc. the cable.
Do not wrap the cable around steam line or otherwise route it in such a manner that the hot steam line could melt the cable.
Do not wrap the cable around steam line or otherwise route it in such a manner that the hot steam line could melt the cable.
Any damage to the control cable will result in the control not working properly.
You will need a 110V recepticle located near the Serenity Light and Music System.
High voltage wires from the transformer must be connected to a 10 AMP minimum, 110 VAC recepticle. Installation must follow national and local building code.
You will need a 110V recepticle located near the Serenity Light and Music System.
High voltage wires from the transformer must be connected to a 10 AMP minimum, 110 VAC recepticle. Installation must follow national and local building code.
Make sure there is no insulation or combustible material within 8 inches of the transformer. No material should touch the transformer.
Bring the 20' control cable from the generator to where the Serenity Light and Music System will be installed.
Cut a hole in desired location per template. The template is located in the Installation and Operation Instructions. Install suitable wood support between joists. Drill the three holes, 7/16" diameter, for mounting of light assembly.
If any external audio devices are used, run audio RCA type cables from the external source to the Serenity Light and Music System. There are 2 audio RCA type inputs available. The Bluetooth Adapter needs one of the RCA inputs to operate.
Mount the transformer in a location that is easily accessible for wiring and inspection. Mount in area where it is out of common contact.
Cut a hole in desired location per template. The template is located in the Installation and Operation Instructions. Install suitable wood support between joists. Drill the three holes, 7/16" diameter, for mounting of light assembly.
If any external audio devices are used, run audio RCA type cables from the external source to the Serenity Light and Music System. There are 2 audio RCA type inputs available. The Bluetooth Adapter needs one of the RCA inputs to operate.
Mount the transformer in a location that is easily accessible for wiring and inspection. Mount in area where it is out of common contact.

For illustrative purposes only. Consult with qualified professional for steam room construction details.
Run Data Cable from the Serenity Light and Music System to where the in-shower control will be installed. Control should be installed 60" from the floor and as far as possible from the steam head and steam emission.
We suggest running control cable through conduit.
We suggest running control cable through conduit.

For illustrative purposes only. Consult with qualified professional for steam room construction details.
Make sure that power to the generator and Serenity Light and Music System is OFF.
Screw-on the data cables carefully lining up contact pins.

Making connections and mounting the Serenity Light and Music System
Now that you have all the cables in place, let's take a look at the Serenity Light and Music System connections.

Connect the following cables and components to the Serenity Light and Music System fixture:
A. Remote Control - Connect supplied Remote 2.4 GHz Antenna
B. From Steam Unit - Connect Data Cable from steam generator
C. To Control - Connect Data Cable from shower control

D. Input 1 - (R & L) Connect Right & Left outputs from Audio Device 1 (Included Bluetooth Adapter)
E. Input 2 - (R & L) Connect Right & Left outputs from Audio Device 2

When connecting the provided Bluetooth Adapter make sure that the 3.5 mm end of the included audio cable is connected all the way in.

F. From 12 VDC - Connect supplied 5.5 mm Transformer Cord
G. From FM Antenna - Connect Coaxial amplified 75 Ω Ohm FM Antenna (not included)
Mounting the Serenity Light and Music System
After you made all the connections it's time to install the fixture itself.
Apply silicone around center of groove on back of the light. Align the screw holes and push the fixture tight against ceiling. Secure the mounting screws from above.

For illustrative purposes only. Consult with qualified professional for steam room construction details.
Comments
0 comments
Please sign in to leave a comment.